Ev v30 06: Water leakage line

This example show how works the Water Leakage (line) in SOCKET_2. The sensor can be connected in SOCKET_1, SOCKET_3 and SOCKET_4 too.

Required Materials

1 x Waspmote 1 x Battery 1 x MiniUSB wire 1 x Events Board v30 1 x Water leakage/detection sensor

Notes

- This example is valid only for Waspmote v15

Code

/*  
 *  --[Ev_v30_06] - Reading liquid presence
 *  
 *  Explanation: This example shows how the Water Leakage (line) works. 
 *  
 *  Copyright (C) 2016 Libelium Comunicaciones Distribuidas S.L. 
 *  http://www.libelium.com 
 *  
 *  This program is free software: you can redistribute it and/or modify 
 *  it under the terms of the GNU General Public License as published by 
 *  the Free Software Foundation, either version 3 of the License, or 
 *  (at your option) any later version. 
 *  
 *  This program is distributed in the hope that it will be useful, 
 *  but WITHOUT ANY WARRANTY; without even the implied warranty of 
 *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the 
 *  GNU General Public License for more details. 
 *  
 *  You should have received a copy of the GNU General Public License 
 *  along with this program.  If not, see <http://www.gnu.org/licenses/>. 
 *  
 *  Version:           3.1
 *  Design:            David Gascón 
 *  Implementation:    Carlos Bello
 */

#include <WaspSensorEvent_v30.h>

/*
 * Define object for sensor. Choose board socket. 
 * Waspmote OEM. Possibilities for this sensor:
 *  - SOCKET_1 
 *  - SOCKET_2
 *  - SOCKET_3
 *  - SOCKET_4
 *  - SOCKET_6
 * P&S! Possibilities for this sensor:
 *  - SOCKET_A
 *  - SOCKET_C
 *  - SOCKET_D
 *  - SOCKET_E
 */
liquidPresenceClass liquidPresence(SOCKET_6);

uint8_t value = 0;
  
void setup() 
{
  // Turn on the USB and print a start message
  USB.ON();
  USB.println(F("Start program"));
  
  // Turn on the sensor board
  Events.ON();
  
  // Enable interruptions from the board
  Events.attachInt();
}

void loop() 
{
  ///////////////////////////////////////
  // 1. Read the sensor level 
  ///////////////////////////////////////

  // Read the sensor level
  value = liquidPresence.readliquidPresence();

  // Print the info
  if (value == 1)
  {      
    USB.println(F("Sensor output: Water detected!"));
  }
  else
  {
    USB.println(F("Sensor output: Water not detected"));    
  }

  ///////////////////////////////////////
  // 2. Go to deep sleep mode  
  ///////////////////////////////////////
  USB.println(F("enter deep sleep"));
  PWR.deepSleep("00:00:00:10", RTC_OFFSET, RTC_ALM1_MODE1, SENSOR_ON);
  USB.ON();
  USB.println(F("wake up\n"));  

  ///////////////////////////////////////
  // 3. Check Interruption Flags
  ///////////////////////////////////////
   
  // 3.1. Check interruption from RTC alarm
  if (intFlag & RTC_INT)
  {   
    USB.println(F("-----------------------------"));
    USB.println(F("RTC INT captured"));
    USB.println(F("-----------------------------"));
  
    // clear flag
    intFlag &= ~(RTC_INT);
  }
  
  // 3.2. Check interruption from Sensor Board
  if (intFlag & SENS_INT)
  {
    // Disable interruptions from the board
    Events.detachInt();
    
    // Load the interruption flag
    Events.loadInt();  
    
    // In case the interruption came from liquid presence
    if (liquidPresence.getInt())
    {
      USB.println(F("-----------------------------"));
      USB.println(F("Interruption from Water Leakage"));
      USB.println(F("-----------------------------"));
    }
    
    // Clean the interruption flag
    intFlag &= ~(SENS_INT);
    
    // Enable interruptions from the board
    Events.attachInt();
  }
}

Output

H#
Start program
Sensor output: Water no detected
enter deep sleep
wake up

Sensor output: Water no detected
-----------------------------
RTC INT captured
-----------------------------
enter deep sleep
...